Follow us on Google Plus! Follow us on YouTube!

American Made Floor Jack

Showing 1 - 24 of 28 Search Results for "american made floor jack"

Items per page 12 | 24 | 48

1 2 of 2 next

Sort By:

2-Ton Low-Profile Floor Jack    2-3/4in to 20in

2-Ton Low-Profile Floor Jack 2-3/4in to 20in

Item #:

2-Ton Low-Profile Floor Jack No. AFF-IN200T 2-Ton Low-Profile Floor Jack 2-Ton Low-Profile Floor Jack   Built with traditional AFF quality, perfect for today’s lower-profile vehicles. The 200T quickly lifts from a low 2-3/4in. to 20in. with AFF’s double-pumper advantage.    Features: Super low pickup height of 2-3/4in. Equipped with a double pump design to increase speed without compromising performance. Universal joint technology and precision release valve for a more controlled release Pinned steel saddle (1in. stud) with rubber pad for added vehicle protection and durability Tough UV powder coated frame for greater protection and durability One-piece foam covered 50in. handle for ease of positioning, pumping and storage. Safety valve prevents overload  Specifications: Capacity    2 Tons Low Height  2-3/4in. High Height  20      Length  27in. Front Width  11-3/4in.         Rear Width  15in. Ship Weight   99 lbs.

PROMO HWA-HW93662 10-Ton Air/Manual Service Jack + HWA-HW7031 Blue Rough Rider Mechanics Creeper + OMG-82002 1/2

PROMO HWA-HW93662 10-Ton Air/Manual Service Jack + HWA-HW7031 Blue Rough Rider Mechanics Creeper + OMG-82002 1/2" Air Impact Wrench

Item #:

HWA-HW93662 Features: • Lifting trucks, trailers, and buses by the axle, differential, or frame • Dual piston action provides speed to contact and power to lift • Long chassis for hard to reach points • Handle adjusts to three pumping positions • T handle with release knob for exact positioning of load • Sealed hydraulic unit keeps out grit, grime and moisture • Large full swivel saddle and ball bearing caster make positioning easy • Cast lift arm for heavy loads • Operates manually or with air • Patented “Speed Pak™” reduces handle pumping • Uses standard shop air 110-175 PSI pressure (140-175 PSI for rated load) • Made in U.S.A. • Capacity: 10 Ton • Min Height: 6 3/4" • Max Height: 25 1/2" • Chassis Length: 53 1/2" • Wheel to Wheel Width: 20 1/2" • Max Air Pressure: 140 PSI • Gross Weight: 435 lbs.HWA-HW7031 Features: • 100% American Made • Rough Rider is made specifically to be used outdoors in less than ideal conditions including dirt, rough pavement, and gravel with a firm substrate • Extremely popular with military, police and other government agencies • Capacity: 400 lbs. • Ground Clearance: 2.875" • Weight: 20 lbs. • Item Dimensions: 45.5" L x 25.5" W x 7.875" H • Wheel size: 5.275"OMG-82002 Features: • Pistol grip design for control and comfort • Low vibration for reduced fatigue • Twin hammer mechanism provides max. 450 ft-lbs torque • Suitable for professional jobs

PROMO HWA-HW93660 10-Ton Manual Service Jack + HWA-HW7031 Blue Rough Rider Mechanics Creeper + OMG-82001 1/2

PROMO HWA-HW93660 10-Ton Manual Service Jack + HWA-HW7031 Blue Rough Rider Mechanics Creeper + OMG-82001 1/2" Drive Mini Air Impact Wrench

Item #:

HWA-HW93660 Features: • Lifting trucks, trailers, and buses by the axle, differential, or frame • Dual piston action provides speed to contact and power to lift • Long chassis for hard to reach points • Handle adjusts to three pumping positions • T handle with release knob for exact positioning of load • Sealed hydraulic unit keeps out grit, grime and moisture • Large full swivel saddle and ball bearing caster make positioning easy • Cast lift arm for heavy loads • Made in U.S.A. • Capacity: 10 Ton • Min Height: 6 3/4" • Max Height: 25 1/1" • Chassis Length: 53 1/2" • Wheel to Wheel Width: 20 1/2" • Gross Weight: 420 lbs.HWA-HW7031 Features: • 100% American Made • Rough Rider is made specifically to be used outdoors in less than ideal conditions including dirt, rough pavement, and gravel with a firm substrate • Extremely popular with military, police and other government agencies • Capacity: 400 lbs. • Ground Clearance: 2.875" • Weight: 20 lbs. • Item Dimensions: 45.5" L x 25.5" W x 7.875" H • Wheel size: 5.275"OMG-82001 Features: • Twin hammer design • ¼” Air Inlet • Max Torque 500 ft-lbs • Pistol grip design for control and comfort • Power to weight ratio for the toughest jobs

28,000lb Cap floor Service Jack

28,000lb Cap floor Service Jack

Item #:

• The Scorpion TJ14 lifts the whole front end or rear end in one go! A conventional jack you have to lift a corner at a time. • The Scorpion TJ14 is the only jack available with a built in three stage locking mechanism so there is no need for vehicle stands! • The Scorpion TJ14 is built to last and is made of the highest-grade materials! • Increased through put for your shop. The TJ14 lifts a truck in seconds! A conventional jacks and two stands takes 7-10 minutes! • Reduce employee fatigue and injuries. The TJ14 keeps your technicians off the floor as much as possible keeping them fresh and alert for the servicing of vehicles. • You preserve your hard earned money buy not throwing it away on jacks that don’t last

1-Ton Floor Style Transmission Jack

1-Ton Floor Style Transmission Jack

Item #:

1-Ton Floor Style Transmission Jack No. LIN-HW93718 1-Ton Floor Style Transmission Jack 1-Ton Floor Style Transmission Jack Features: Wishbone design allows unit more mobility Tubular steel frame 360 degree swivel casters Load restraint chain MADE IN USA Designed for heavy duty transmissions: Fuller road rangers Spicer 50,60,5000,6000 and split torque (SST) series Mack T-2000 and Maxitorque series Allison AT, MT and HT series Clark 280, 282, 285, CL455 and CL550 Mercedes G3 and GV4 types Volvo S & R models Iveco 31, 35, 46 and 2828 models Specifications: Capacity Min. Height Max. Height Chassis Length Chassis Width 1-Ton 10-1/4in. 44-3/4in. 47-3/8in. 28-1/4in. Forward Tilt Rear Tilt Sideways Tilt G.W 44 degrees 39 degrees 13 degrees Left, Right 310lbs.

Aircraft Jack, 30in to 52in, 24000 lb. capacity A330C

Aircraft Jack, 30in to 52in, 24000 lb. capacity A330C

Item #:

table > Aircraft Jack, 30 to 52in, 24000lb. capacityToday's jet and turbo-prop aircraft weighing up to 32,000 lbs. are too valuable to consider using anything less than the A300 Series Aircraft Jacks from Meyer Hydraulics. For over 45 years, Meyer Hydraulics has manufactured aircraft jacks that continue to set the standard for safe, dependable lifting. This line of professional lifting equipment handles aircraft weighing up to 32,000 pounds with the security and features one should demand in an aircraft jack. Industry standard Meyer Hydraulics Aircraft Jacks feature positive pin safety locks, spring loaded casters and special Meyer locking device to eliminate motion when aircraft is elevated. Painted Hi-visibility AN Yellow. MADE IN THE USA SEE AIRCRAFT JACKS & ACCESSORIES APPLICATION CHART for lifting equipment necessary for certain aircraft. Click Here To View Application Chart Features:ANTI-SWAY ANTI-SNAG GUIDANCE SLEEVES CONVENIENT HOLE SPACING POSITIVE SAFETY LOCK Spring loaded safety pin pops into the slide tube to prevent accidental lowering LARGE DIAMETER ROUND FRAME TUBE SIX 3in. SPRING LOADED CASTERS The steel leg pads never scuff across the hanger floorLOW HEIGHT LEG DESIGN Provides maximum gear door clearance with one section completely free of any protrusions. The three 26in. legs create a wide stance insuring stability. A300 Series Aircraft Jacks & Accessories Chart Jack Model No. Old No. Capacity Low High Lifting Range Special Slide Tubes Available* A322B A-10 16,000 lbs. 22in. 36in. 14in. AT32224 to AT32236 A325B A-2516 16,000 lbs. 25in. 42in. 17in. AT32527 to AT32542A328B A-9 16,000 lbs. 28in. 48in. 20in. AT32830 to AT32848 A330B A-11 16,000 lbs. 30in. 52in. 22in. AT33032 to AT33052 A330C   24,000 lbs. 30in. 52in. 22in.  A334B A-17 16,000 lbs. 34in. 60in. 26in. AT33436 to AT33460 A334C A-1724 24,000 lbs. 34in. 60in. 26in. AT33436 to AT33460A340C A-15 24,000 lbs. 40in. 71in. 31in. AT34042 to AT34069 A342B A-13 16,000 lbs. 42in. 75in. 33in. AT34244 to AT34267A342C A-1324 24,000 lbs. 42in. 75in. 33in. AT34244 to AT34267 A355C A-5524 24,000 lbs. 55in. 95in. 40in. AT35557 to AT35560A360A A-60 10,000 lbs. 60in. 100in. 40in. none

Service Floor Jack 2 Ton Capacity

Service Floor Jack 2 Ton Capacity

Item #:

Service Floor Jack 2 Ton Capacity No. LIN-HW93642 Service Floor Jack 2 Ton Capacity Service Floor Jack 2 Ton Capacity "True Blue 642" is the benchmark for service jacks within the lifting industry. This rugged built jack is dependable and designed to deliver a long life of exceptional service. Marquette service jacks feature shielded hydraulic pumps to protect from contamination.   Features: Low 3.75in. pick up height. Crushed metal fittings eliminate rubber gaskets to extend jack life. U-Joint hydraulic release for controlled lowering. Cast iron bell crank for durability. Automatic valve prevents overloading. Flanged side plates for increased strength. Made in the USA Specifications: Capacity: 2 Ton Low height: 3.75in. High Height: 20in. Power Raise: 16.25in. Cap Diameter: 5.75in Handle Length: 50in. Chassis Length: 26.75in. Chassis Height: 6.75in. Front Wheel Dia: 3.75in. Caster Wheel Dia: 2.5in.

Service Floor Jack 6-Ton Air Hydraulic

Service Floor Jack 6-Ton Air Hydraulic

Item #:

OTC-5106 Service Floor Jack 6-Ton Air HydraulicService Floor Jacks Air Hydraulic 6 & 10 Ton Capacity OTCThese new OTC jacks bring the versatility of air-assist operation to your shop's lifting tasks. The no. 235-5110 10-ton model can also be operated manually when shop air is unavailable. Both jacks are constructed of the highest quality steel frame members to stand up to the kind of abuse jacks are subjected to daily. Each has a low starting height to add to their versatility. Huge steel front wheels are mounted in bearings for trouble-free service life. Rear swivel casters make spotting the jack an easy task. Spring-loaded handle can be locked in three positions, from horizontal to vertical. Made In U.S.A. 

Aircraft Jack 34in to 60in, 16000 lb. capacity

Aircraft Jack 34in to 60in, 16000 lb. capacity

Item #:

Aircraft Jack, 34 to 60in, 16000 lb. capacity (Formerly MYR-A-17) Today's jet and turbo-prop aircraft weighing up to 32,000 lbs. are too valuable to consider using anything less than the A300 Series Aircraft Jacks from Meyer Hydraulics. For over 45 years, Meyer Hydraulics has manufactured aircraft jacks that continue to set the standard for safe, dependable lifting. This line of professional lifting equipment handles aircraft weighing up to 32,000 pounds with the security and features one should demand in an aircraft jack. Industry standard Meyer Hydraulics Aircraft Jacks feature positive pin safety locks, spring loaded casters and special Meyer locking device to eliminate motion when aircraft is elevated. Painted Hi-visibility AN Yellow. MADE IN THE USA SEE AIRCRAFT JACKS & ACCESSORIES APPLICATION CHART for lifting equipment necessary for certain aircraft. Click Here To View Application Chart Features: ANTI-SWAY ANTI-SNAG GUIDANCE SLEEVES CONVENIENT HOLE SPACING POSITIVE SAFETY LOCK Spring loaded safety pin pops into the slide tube to prevent accidental lowering LARGE DIAMETER ROUND FRAME TUBE SIX 3in. SPRING LOADED CASTERS The steel leg pads never scuff across the hanger floor LOW HEIGHT LEG DESIGN Provides maximum gear door clearance with one section completely free of any protrusions. The three 26in. legs create a wide stance insuring stability. A300 Series Aircraft Jacks & Accessories Chart Jack Model No. Old No. Capacity Low High Lifting Range Special Slide Tubes Available* A322B A-10 16,000 lbs. 22in. 36in. 14in. AT32224 to AT32236 A325B A-2516 16,000 lbs. 25in. 42in. 17in. AT32527 to AT32542A328B A-9 16,000 lbs. 28in. 48in. 20in. AT32830 to AT32848 A330B A-11 16,000 lbs. 30in. 52in. 22in. AT33032 to AT33052A334B A-17 16,000 lbs. 34in. 60in. 26in. AT33436 to AT33460 A334C A-1724 24,000 lbs. 34in. 60in. 26in. AT33436 to AT33460A340C A-15 24,000 lbs. 40in. 71in. 31in. AT34042 to AT34069 A342B A-13 16,000 lbs. 42in. 75in. 33in. AT34244 to AT34267A342C A-1324 24,000 lbs. 42in. 75in. 33in. AT34244 to AT34267 A355C A-5524 24,000 lbs. 55in. 95in. 40in. AT35557 to AT35560A360A A-60 10,000 lbs. 60in. 100in. 40in. none

Aircraft Jack 60in to 100in, 10000 lb. Capacity

Aircraft Jack 60in to 100in, 10000 lb. Capacity

Item #:

Aircraft Jack, 60 to 100in, 10000 lb. capacity (Formerly MYR-A-60) Today's jet and turbo-prop aircraft weighing up to 32,000 lbs. are too valuable to consider using anything less than the A300 Series Aircraft Jacks from Meyer Hydraulics. For over 45 years, Meyer Hydraulics has manufactured aircraft jacks that continue to set the standard for safe, dependable lifting. This line of professional lifting equipment handles aircraft weighing up to 32,000 pounds with the security and features one should demand in an aircraft jack. Industry standard Meyer Hydraulics Aircraft Jacks feature positive pin safety locks, spring loaded casters and special Meyer locking device to eliminate motion when aircraft is elevated. Painted Hi-visibility AN Yellow. MADE IN THE USA SEE AIRCRAFT JACKS & ACCESSORIES APPLICATION CHART for lifting equipment necessary for certain aircraft. Click Here To View Application Chart Features: ANTI-SWAY ANTI-SNAG GUIDANCE SLEEVES CONVENIENT HOLE SPACING POSITIVE SAFETY LOCK Spring loaded safety pin pops into the slide tube to prevent accidental lowering LARGE DIAMETER ROUND FRAME TUBE SIX 3in. SPRING LOADED CASTERS The steel leg pads never scuff across the hanger floor LOW HEIGHT LEG DESIGN Provides maximum gear door clearance with one section completely free of any protrusions. The three 26in. legs create a wide stance insuring stability. A300 Series Aircraft Jacks & Accessories Chart Jack Model No. Old No. Capacity Low High Lifting Range Special Slide Tubes Available* A322B A-10 16,000 lbs. 22in. 36in. 14in. AT32224 to AT32236 A325B A-2516 16,000 lbs. 25in. 42in. 17in. AT32527 to AT32542A328B A-9 16,000 lbs. 28in. 48in. 20in. AT32830 to AT32848 A330B A-11 16,000 lbs. 30in. 52in. 22in. AT33032 to AT33052A334B A-17 16,000 lbs. 34in. 60in. 26in. AT33436 to AT33460 A334C A-1724 24,000 lbs. 34in. 60in. 26in. AT33436 to AT33460A340C A-15 24,000 lbs. 40in. 71in. 31in. AT34042 to AT34069 A342B A-13 16,000 lbs. 42in. 75in. 33in. AT34244 to AT34267A342C A-1324 24,000 lbs. 42in. 75in. 33in. AT34244 to AT34267 A355C A-5524 24,000 lbs. 55in. 95in. 40in. AT35557 to AT35560A360A A-60 10,000 lbs. 60in. 100in. 40in. none

Aircraft Jack 42in to 75in, 24000 lb. capacity

Aircraft Jack 42in to 75in, 24000 lb. capacity

Item #:

Aircraft Jack, 42 to 75in, 24000 lb. capacity (Formerly MYR-A-1324) Today's jet and turbo-prop aircraft weighing up to 32,000 lbs. are too valuable to consider using anything less than the A300 Series Aircraft Jacks from Meyer Hydraulics. For over 45 years, Meyer Hydraulics has manufactured aircraft jacks that continue to set the standard for safe, dependable lifting. This line of professional lifting equipment handles aircraft weighing up to 32,000 pounds with the security and features one should demand in an aircraft jack. Industry standard Meyer Hydraulics Aircraft Jacks feature positive pin safety locks, spring loaded casters and special Meyer locking device to eliminate motion when aircraft is elevated. Painted Hi-visibility AN Yellow. MADE IN THE USA SEE AIRCRAFT JACKS & ACCESSORIES APPLICATION CHART for lifting equipment necessary for certain aircraft. Click Here To View Application Chart Features: ANTI-SWAY ANTI-SNAG GUIDANCE SLEEVES CONVENIENT HOLE SPACING POSITIVE SAFETY LOCK Spring loaded safety pin pops into the slide tube to prevent accidental lowering LARGE DIAMETER ROUND FRAME TUBE SIX 3in. SPRING LOADED CASTERS The steel leg pads never scuff across the hanger floor LOW HEIGHT LEG DESIGN Provides maximum gear door clearance with one section completely free of any protrusions. The three 26in. legs create a wide stance insuring stability. A300 Series Aircraft Jacks & Accessories Chart Jack Model No. Old No. Capacity Low High Lifting Range Special Slide Tubes Available* A322B A-10 16,000 lbs. 22in. 36in. 14in. AT32224 to AT32236 A325B A-2516 16,000 lbs. 25in. 42in. 17in. AT32527 to AT32542A328B A-9 16,000 lbs. 28in. 48in. 20in. AT32830 to AT32848 A330B A-11 16,000 lbs. 30in. 52in. 22in. AT33032 to AT33052A334B A-17 16,000 lbs. 34in. 60in. 26in. AT33436 to AT33460 A334C A-1724 24,000 lbs. 34in. 60in. 26in. AT33436 to AT33460A340C A-15 24,000 lbs. 40in. 71in. 31in. AT34042 to AT34069 A342B A-13 16,000 lbs. 42in. 75in. 33in. AT34244 to AT34267A342C A-1324 24,000 lbs. 42in. 75in. 33in. AT34244 to AT34267 A355C A-5524 24,000 lbs. 55in. 95in. 40in. AT35557 to AT35560A360A A-60 10,000 lbs. 60in. 100in. 40in. none

Aircraft Jack  42in to 75in, 16000 lb. capacity

Aircraft Jack 42in to 75in, 16000 lb. capacity

Item #:

Aircraft Jack, 42 to 75in, 16000 lb. capacity (Formerly MYR-A-13) Today's jet and turbo-prop aircraft weighing up to 32,000 lbs. are too valuable to consider using anything less than the A300 Series Aircraft Jacks from Meyer Hydraulics. For over 45 years, Meyer Hydraulics has manufactured aircraft jacks that continue to set the standard for safe, dependable lifting. This line of professional lifting equipment handles aircraft weighing up to 32,000 pounds with the security and features one should demand in an aircraft jack. Industry standard Meyer Hydraulics Aircraft Jacks feature positive pin safety locks, spring loaded casters and special Meyer locking device to eliminate motion when aircraft is elevated. Painted Hi-visibility AN Yellow. MADE IN THE USA SEE AIRCRAFT JACKS & ACCESSORIES APPLICATION CHART for lifting equipment necessary for certain aircraft. Click Here To View Application Chart Features: ANTI-SWAY ANTI-SNAG GUIDANCE SLEEVES CONVENIENT HOLE SPACING POSITIVE SAFETY LOCK Spring loaded safety pin pops into the slide tube to prevent accidental lowering LARGE DIAMETER ROUND FRAME TUBE SIX 3in. SPRING LOADED CASTERS The steel leg pads never scuff across the hanger floor LOW HEIGHT LEG DESIGN Provides maximum gear door clearance with one section completely free of any protrusions. The three 26in. legs create a wide stance insuring stability. A300 Series Aircraft Jacks & Accessories Chart Jack Model No. Old No. Capacity Low High Lifting Range Special Slide Tubes Available* A322B A-10 16,000 lbs. 22in. 36in. 14in. AT32224 to AT32236 A325B A-2516 16,000 lbs. 25in. 42in. 17in. AT32527 to AT32542A328B A-9 16,000 lbs. 28in. 48in. 20in. AT32830 to AT32848 A330B A-11 16,000 lbs. 30in. 52in. 22in. AT33032 to AT33052A334B A-17 16,000 lbs. 34in. 60in. 26in. AT33436 to AT33460 A334C A-1724 24,000 lbs. 34in. 60in. 26in. AT33436 to AT33460A340C A-15 24,000 lbs. 40in. 71in. 31in. AT34042 to AT34069 A342B A-13 16,000 lbs. 42in. 75in. 33in. AT34244 to AT34267A342C A-1324 24,000 lbs. 42in. 75in. 33in. AT34244 to AT34267 A355C A-5524 24,000 lbs. 55in. 95in. 40in. AT35557 to AT35560A360A A-60 10,000 lbs. 60in. 100in. 40in. none

Aircraft Jack 40in to 71in, 24000 lb. capacity

Aircraft Jack 40in to 71in, 24000 lb. capacity

Item #:

Aircraft Jack, 40 to 71in, 24000 lb. capacity (Formerly MYR-A-15) Today's jet and turbo-prop aircraft weighing up to 32,000 lbs. are too valuable to consider using anything less than the A300 Series Aircraft Jacks from Meyer Hydraulics. For over 45 years, Meyer Hydraulics has manufactured aircraft jacks that continue to set the standard for safe, dependable lifting. This line of professional lifting equipment handles aircraft weighing up to 32,000 pounds with the security and features one should demand in an aircraft jack. Industry standard Meyer Hydraulics Aircraft Jacks feature positive pin safety locks, spring loaded casters and special Meyer locking device to eliminate motion when aircraft is elevated. Painted Hi-visibility AN Yellow. MADE IN THE USA SEE AIRCRAFT JACKS & ACCESSORIES APPLICATION CHART for lifting equipment necessary for certain aircraft. Click Here To View Application Chart Features: ANTI-SWAY ANTI-SNAG GUIDANCE SLEEVES CONVENIENT HOLE SPACING POSITIVE SAFETY LOCK Spring loaded safety pin pops into the slide tube to prevent accidental lowering LARGE DIAMETER ROUND FRAME TUBE SIX 3in. SPRING LOADED CASTERS The steel leg pads never scuff across the hanger floor LOW HEIGHT LEG DESIGN Provides maximum gear door clearance with one section completely free of any protrusions. The three 26in. legs create a wide stance insuring stability. A300 Series Aircraft Jacks & Accessories Chart Jack Model No. Old No. Capacity Low High Lifting Range Special Slide Tubes Available* A322B A-10 16,000 lbs. 22in. 36in. 14in. AT32224 to AT32236 A325B A-2516 16,000 lbs. 25in. 42in. 17in. AT32527 to AT32542A328B A-9 16,000 lbs. 28in. 48in. 20in. AT32830 to AT32848 A330B A-11 16,000 lbs. 30in. 52in. 22in. AT33032 to AT33052A334B A-17 16,000 lbs. 34in. 60in. 26in. AT33436 to AT33460 A334C A-1724 24,000 lbs. 34in. 60in. 26in. AT33436 to AT33460A340C A-15 24,000 lbs. 40in. 71in. 31in. AT34042 to AT34069 A342B A-13 16,000 lbs. 42in. 75in. 33in. AT34244 to AT34267A342C A-1324 24,000 lbs. 42in. 75in. 33in. AT34244 to AT34267 A355C A-5524 24,000 lbs. 55in. 95in. 40in. AT35557 to AT35560A360A A-60 10,000 lbs. 60in. 100in. 40in. none

Aircraft Jack 34in to 60in, 24000 lb. capacity

Aircraft Jack 34in to 60in, 24000 lb. capacity

Item #:

Aircraft Jack, 34 to 60in, 24000 lb. capacity (Formerly MYR-A-1724) Today's jet and turbo-prop aircraft weighing up to 32,000 lbs. are too valuable to consider using anything less than the A300 Series Aircraft Jacks from Meyer Hydraulics. For over 45 years, Meyer Hydraulics has manufactured aircraft jacks that continue to set the standard for safe, dependable lifting. This line of professional lifting equipment handles aircraft weighing up to 32,000 pounds with the security and features one should demand in an aircraft jack. Industry standard Meyer Hydraulics Aircraft Jacks feature positive pin safety locks, spring loaded casters and special Meyer locking device to eliminate motion when aircraft is elevated. Painted Hi-visibility AN Yellow. MADE IN THE USA SEE AIRCRAFT JACKS & ACCESSORIES APPLICATION CHART for lifting equipment necessary for certain aircraft. Click Here To View Application Chart Features: ANTI-SWAY ANTI-SNAG GUIDANCE SLEEVES CONVENIENT HOLE SPACING POSITIVE SAFETY LOCK Spring loaded safety pin pops into the slide tube to prevent accidental lowering LARGE DIAMETER ROUND FRAME TUBE SIX 3in. SPRING LOADED CASTERS The steel leg pads never scuff across the hanger floor LOW HEIGHT LEG DESIGN Provides maximum gear door clearance with one section completely free of any protrusions. The three 26in. legs create a wide stance insuring stability. A300 Series Aircraft Jacks & Accessories Chart Jack Model No. Old No. Capacity Low High Lifting Range Special Slide Tubes Available* A322B A-10 16,000 lbs. 22in. 36in. 14in. AT32224 to AT32236 A325B A-2516 16,000 lbs. 25in. 42in. 17in. AT32527 to AT32542A328B A-9 16,000 lbs. 28in. 48in. 20in. AT32830 to AT32848 A330B A-11 16,000 lbs. 30in. 52in. 22in. AT33032 to AT33052A334B A-17 16,000 lbs. 34in. 60in. 26in. AT33436 to AT33460 A334C A-1724 24,000 lbs. 34in. 60in. 26in. AT33436 to AT33460A340C A-15 24,000 lbs. 40in. 71in. 31in. AT34042 to AT34069 A342B A-13 16,000 lbs. 42in. 75in. 33in. AT34244 to AT34267A342C A-1324 24,000 lbs. 42in. 75in. 33in. AT34244 to AT34267 A355C A-5524 24,000 lbs. 55in. 95in. 40in. AT35557 to AT35560A360A A-60 10,000 lbs. 60in. 100in. 40in. none

Aircraft Jack 30 to 52in, 16000 lb. capacity

Aircraft Jack 30 to 52in, 16000 lb. capacity

Item #:

Aircraft Jack, 30 to 52in, 16000 lb. capacity (Formerly MYR-A-11) Today's jet and turbo-prop aircraft weighing up to 32,000 lbs. are too valuable to consider using anything less than the A300 Series Aircraft Jacks from Meyer Hydraulics. For over 45 years, Meyer Hydraulics has manufactured aircraft jacks that continue to set the standard for safe, dependable lifting. This line of professional lifting equipment handles aircraft weighing up to 32,000 pounds with the security and features one should demand in an aircraft jack. Industry standard Meyer Hydraulics Aircraft Jacks feature positive pin safety locks, spring loaded casters and special Meyer locking device to eliminate motion when aircraft is elevated. Painted Hi-visibility AN Yellow. MADE IN THE USA SEE AIRCRAFT JACKS & ACCESSORIES APPLICATION CHART for lifting equipment necessary for certain aircraft. Click Here To View Application Chart Features: ANTI-SWAY ANTI-SNAG GUIDANCE SLEEVES CONVENIENT HOLE SPACING POSITIVE SAFETY LOCK Spring loaded safety pin pops into the slide tube to prevent accidental lowering LARGE DIAMETER ROUND FRAME TUBE SIX 3in. SPRING LOADED CASTERS The steel leg pads never scuff across the hanger floor LOW HEIGHT LEG DESIGN Provides maximum gear door clearance with one section completely free of any protrusions. The three 26in. legs create a wide stance insuring stability. A300 Series Aircraft Jacks & Accessories Chart Jack Model No. Old No. Capacity Low High Lifting Range Special Slide Tubes Available* A322B A-10 16,000 lbs. 22in. 36in. 14in. AT32224 to AT32236 A325B A-2516 16,000 lbs. 25in. 42in. 17in. AT32527 to AT32542A328B A-9 16,000 lbs. 28in. 48in. 20in. AT32830 to AT32848 A330B A-11 16,000 lbs. 30in. 52in. 22in. AT33032 to AT33052A334B A-17 16,000 lbs. 34in. 60in. 26in. AT33436 to AT33460 A334C A-1724 24,000 lbs. 34in. 60in. 26in. AT33436 to AT33460A340C A-15 24,000 lbs. 40in. 71in. 31in. AT34042 to AT34069 A342B A-13 16,000 lbs. 42in. 75in. 33in. AT34244 to AT34267A342C A-1324 24,000 lbs. 42in. 75in. 33in. AT34244 to AT34267 A355C A-5524 24,000 lbs. 55in. 95in. 40in. AT35557 to AT35560A360A A-60 10,000 lbs. 60in. 100in. 40in. none

Aircraft Jack 28in to 48in, 16000 lb. capacity

Aircraft Jack 28in to 48in, 16000 lb. capacity

Item #:

Aircraft Jack, 28 to 48in, 16000 lb. capacity (Formerly MYR-A-9) Today's jet and turbo-prop aircraft weighing up to 32,000 lbs. are too valuable to consider using anything less than the A300 Series Aircraft Jacks from Meyer Hydraulics. For over 45 years, Meyer Hydraulics has manufactured aircraft jacks that continue to set the standard for safe, dependable lifting. This line of professional lifting equipment handles aircraft weighing up to 32,000 pounds with the security and features one should demand in an aircraft jack. Industry standard Meyer Hydraulics Aircraft Jacks feature positive pin safety locks, spring loaded casters and special Meyer locking device to eliminate motion when aircraft is elevated. Painted Hi-visibility AN Yellow. MADE IN THE USA SEE AIRCRAFT JACKS & ACCESSORIES APPLICATION CHART for lifting equipment necessary for certain aircraft. Click Here To View Application Chart Features: ANTI-SWAY ANTI-SNAG GUIDANCE SLEEVES CONVENIENT HOLE SPACING POSITIVE SAFETY LOCK Spring loaded safety pin pops into the slide tube to prevent accidental lowering LARGE DIAMETER ROUND FRAME TUBE SIX 3in. SPRING LOADED CASTERS The steel leg pads never scuff across the hanger floor LOW HEIGHT LEG DESIGN Provides maximum gear door clearance with one section completely free of any protrusions. The three 26in. legs create a wide stance insuring stability. A300 Series Aircraft Jacks & Accessories Chart Jack Model No. Old No. Capacity Low High Lifting Range Special Slide Tubes Available* A322B A-10 16,000 lbs. 22in. 36in. 14in. AT32224 to AT32236 A325B A-2516 16,000 lbs. 25in. 42in. 17in. AT32527 to AT32542A328B A-9 16,000 lbs. 28in. 48in. 20in. AT32830 to AT32848 A330B A-11 16,000 lbs. 30in. 52in. 22in. AT33032 to AT33052A334B A-17 16,000 lbs. 34in. 60in. 26in. AT33436 to AT33460 A334C A-1724 24,000 lbs. 34in. 60in. 26in. AT33436 to AT33460A340C A-15 24,000 lbs. 40in. 71in. 31in. AT34042 to AT34069 A342B A-13 16,000 lbs. 42in. 75in. 33in. AT34244 to AT34267A342C A-1324 24,000 lbs. 42in. 75in. 33in. AT34244 to AT34267 A355C A-5524 24,000 lbs. 55in. 95in. 40in. AT35557 to AT35560A360A A-60 10,000 lbs. 60in. 100in. 40in. none

Aircraft Jack  22in to 36in, 16000 lb. capacity

Aircraft Jack 22in to 36in, 16000 lb. capacity

Item #:

Aircraft Jack, 22 to 36in, 16000 lb. capacity (Formerly MYR-A-10) Today's jet and turbo-prop aircraft weighing up to 32,000 lbs. are too valuable to consider using anything less than the A300 Series Aircraft Jacks from Meyer Hydraulics. For over 45 years, Meyer Hydraulics has manufactured aircraft jacks that continue to set the standard for safe, dependable lifting. This line of professional lifting equipment handles aircraft weighing up to 32,000 pounds with the security and features one should demand in an aircraft jack. Industry standard Meyer Hydraulics Aircraft Jacks feature positive pin safety locks, spring loaded casters and special Meyer locking device to eliminate motion when aircraft is elevated. Painted Hi-visibility AN Yellow. MADE IN THE USA SEE AIRCRAFT JACKS & ACCESSORIES APPLICATION CHART for lifting equipment necessary for certain aircraft. Click Here To View Application Chart Features: ANTI-SWAY ANTI-SNAG GUIDANCE SLEEVES CONVENIENT HOLE SPACING POSITIVE SAFETY LOCK Spring loaded safety pin pops into the slide tube to prevent accidental lowering LARGE DIAMETER ROUND FRAME TUBE SIX 3in. SPRING LOADED CASTERS The steel leg pads never scuff across the hanger floor LOW HEIGHT LEG DESIGN Provides maximum gear door clearance with one section completely free of any protrusions. The three 26in. legs create a wide stance insuring stability. A300 Series Aircraft Jacks & Accessories Chart Jack Model No. Old No. Capacity Low High Lifting Range Special Slide Tubes Available* A322B A-10 16,000 lbs. 22in. 36in. 14in. AT32224 to AT32236 A325B A-2516 16,000 lbs. 25in. 42in. 17in. AT32527 to AT32542A328B A-9 16,000 lbs. 28in. 48in. 20in. AT32830 to AT32848 A330B A-11 16,000 lbs. 30in. 52in. 22in. AT33032 to AT33052A334B A-17 16,000 lbs. 34in. 60in. 26in. AT33436 to AT33460 A334C A-1724 24,000 lbs. 34in. 60in. 26in. AT33436 to AT33460A340C A-15 24,000 lbs. 40in. 71in. 31in. AT34042 to AT34069 A342B A-13 16,000 lbs. 42in. 75in. 33in. AT34244 to AT34267A342C A-1324 24,000 lbs. 42in. 75in. 33in. AT34244 to AT34267 A355C A-5524 24,000 lbs. 55in. 95in. 40in. AT35557 to AT35560A360A A-60 10,000 lbs. 60in. 100in. 40in. none

Aircraft Jack (VeryLow) 21in to 38in, 6000 lb. capacity

Aircraft Jack (VeryLow) 21in to 38in, 6000 lb. capacity

Item #:

Aircraft Jack (VeryLow) 21in-38in. 6000lb. CapacityVeryLow Aircraft Jacks - Designed primarily for the new class of aircraft called Very Light Jets (VLJs). Each jack features an ultra low height and the maximum stroke range necessary for the large landing gear movements found on these jets.The A400 Series from Meyer Hydraulics has served as the general aviation industry standard for over 45 years. Professional service technicians rely on the A400 Series for the confident lifting of aircraft weighing up to 8,000 lbs. with the security and features one should demand in aircraft jacks. MADE IN THE USA SEE AIRCRAFT JACKS & ACCESSORIES APPLICATION CHART for lifting equipment necessary for certain aircraft. Click Here To View Application Chart Features: STEADY KNOBS Prevent motion when aircraft is elevated CONVENIENT HOLE SPACING POSITIVE SAFETY LOCK Spring loaded safety pin pops into the slide tube to prevent accidental lowering. ANTI-SNAG ROUND TUBE THREE 3in. SPRING LOADED CASTERS The steel leg tips never scuff across the hanger floor LOW-HEIGHT LEG DESIGN Provides maximum gear door clearance with one section completely free of any protrusions. The 4 legs insure excellent stability. Specifications: A400 Series Items Height Ranges A419 Jack 19in./34in. A421 Jack 21in./38in. A422 Jack w/ AT42222* 22in./36in. A422 Jack w/ AT42228 28in./42in. A422 Jack w/ AT 42234 34in./48in. A427 Jack w/ AT42727* 27in./46in. A434 Jack w/ AT43434* 34in./58in. A434 Jack w/ AT43454 54in./78in. A434 Jack w/ AJL Legs +10in. ATC-4 Cap +1 to 4in. ATC-8 Cap +1 to 8in. ATS Tailstand 30in./51in. ATS w/ATS-AA72 Tube 51in./72in. * ATC Caps will not work on these Tubes

Aircraft Jack 34in to 58in, 6000 lb. capacity w/AT43434 Tube

Aircraft Jack 34in to 58in, 6000 lb. capacity w/AT43434 Tube

Item #:

Aircraft Jack, 34in-58in. 6000lb. Capacity w/AT43434 TubeThe A400 Series from Meyer Hydraulics has served as the general aviation industry standard for over 45 years. Professional service technicians rely on the A400 Series for the confident lifting of aircraft weighing up to 8,000 lbs. with the security and features one should demand in aircraft jacks. MADE IN THE USA SEE AIRCRAFT JACKS & ACCESSORIES APPLICATION CHART for lifting equipment necessary for certain aircraft. Click Here To View Application Chart Features: STEADY KNOBS Prevent motion when aircraft is elevated CONVENIENT HOLE SPACING POSITIVE SAFETY LOCK Spring loaded safety pin pops into the slide tube to prevent accidental lowering. ANTI-SNAG ROUND TUBE THREE 3in. SPRING LOADED CASTERS The steel leg tips never scuff across the hanger floor LOW-HEIGHT LEG DESIGN Provides maximum gear door clearance with one section completely free of any protrusions. The 4 legs insure excellent stability Specifications: A400 Series Items Height Ranges A419 Jack 19in./34in. A421 Jack 21in./38in. A422 Jack w/ AT42222* 22in./36in. A422 Jack w/ AT42228 28in./42in. A422 Jack w/ AT 42234 34in./48in. A427 Jack w/ AT42727* 27in./46in. A434 Jack w/ AT43434* 34in./58in. A434 Jack w/ AT43454 54in./78in. A434 Jack w/ AJL Legs +10in. ATC-4 Cap +1 to 4in. ATC-8 Cap +1 to 8in. ATS Tailstand 30in./51in. ATS w/ATS-AA72 Tube 51in./72in. * ATC Caps will not work on these Tubes

Aircraft Jack 22in to 36in, 6000 lb. capacity  w/AT42222 Tube

Aircraft Jack 22in to 36in, 6000 lb. capacity w/AT42222 Tube

Item #:

(Former Part No. MYR-A-5) The A400 Series from Meyer Hydraulics has served as the general aviation industry standard for over 45 years. Professional service technicians rely on the A400 Series for the confident lifting of aircraft weighing up to 8,000 lbs. with the security and features one should demand in aircraft jacks. MADE IN THE USA SEE AIRCRAFT JACKS & ACCESSORIES APPLICATION CHART for lifting equipment necessary for certain aircraft. Click Here To View Application Chart Features: STEADY KNOBS Prevent motion when aircraft is elevated CONVENIENT HOLE SPACING POSITIVE SAFETY LOCK Spring loaded safety pin pops into the slide tube to prevent accidental lowering. ANTI-SNAG ROUND TUBE THREE 3in. SPRING LOADED CASTERS The steel leg tips never scuff across the hanger floor LOW-HEIGHT LEG DESIGN Provides maximum gear door clearance with one section completely free of any protrusions. The 4 legs insure excellent stability. Specifications: A400 Series Items Height Ranges A419 Jack 19in./34in. A421 Jack 21in./38in. A422 Jack w/ AT42222* 22in./36in. A422 Jack w/ AT42228 28in./42in. A422 Jack w/ AT 42234 34in./48in. A427 Jack w/ AT42727* 27in./46in. A434 Jack w/ AT43434* 34in./58in. A434 Jack w/ AT43454 54in./78in. A434 Jack w/ AJL Legs +10in. ATC-4 Cap +1 to 4in. ATC-8 Cap +1 to 8in. ATS Tailstand 30in./51in. ATS w/ATS-AA72 Tube 51in./72in. * ATC Caps will not work on these Tubes

Aircraft Jack (VeryLow) 19in to 34in, 6000 lb. capacity

Aircraft Jack (VeryLow) 19in to 34in, 6000 lb. capacity

Item #:

Aircraft Jack (VeryLow) 19in-34in. 6000lb. CapacityVeryLow Aircraft Jacks - Designed primarily for the new class of aircraft called Very Light Jets (VLJs). Each jack features an ultra low height and the maximum stroke range necessary for the large landing gear movements found on these jets.The A400 Series from Meyer Hydraulics has served as the general aviation industry standard for over 45 years. Professional service technicians rely on the A400 Series for the confident lifting of aircraft weighing up to 8,000 lbs. with the security and features one should demand in aircraft jacks.MADE IN THE USA SEE AIRCRAFT JACKS & ACCESSORIES APPLICATION CHART for lifting equipment necessary for certain aircraft. Click Here To View Application Chart Features: STEADY KNOBS Prevent motion when aircraft is elevated CONVENIENT HOLE SPACING POSITIVE SAFETY LOCK Spring loaded safety pin pops into the slide tube to prevent accidental lowering. ANTI-SNAG ROUND TUBE THREE 3in. SPRING LOADED CASTERS The steel leg tips never scuff across the hanger floor LOW-HEIGHT LEG DESIGN Provides maximum gear door clearance with one section completely free of any protrusions. The 4 legs insure excellent stability. Specifications: A400 Series Items Height Ranges A419 Jack 19in./34in. A421 Jack 21in./38in. A422 Jack w/ AT42222* 22in./36in. A422 Jack w/ AT42228 28in./42in. A422 Jack w/ AT 42234 34in./48in. A427 Jack w/ AT42727* 27in./46in. A434 Jack w/ AT43434* 34in./58in. A434 Jack w/ AT43454 54in./78in. A434 Jack w/ AJL Legs +10in. ATC-4 Cap +1 to 4in. ATC-8 Cap +1 to 8in. ATS Tailstand 30in./51in. ATS w/ATS-AA72 Tube 51in./72in. * ATC Caps will not work on these Tubes

Tail Bone Creeper

Tail Bone Creeper

Item #:

The Tail Bone Mechanics Seat The Tail Bone is a totally new approach to creeper seats, designed from scratch to be easier to use, more comfortable, more durable and a better value than any other mechanic's stool on the market! The same big 5in diameter wheels that made Bone creepers so popular and famous let the Tail Bone roll effortlessly over air hoses, drop cords, shop clutter, rough surfaces and much more.The base is a uniquely designed tripod, so it's a naturally stable working platform even on uneven floors and surfaces. And because it turns with the user, the legs always stay out of the way and let you tuck your feet under you for comfort or convenience. The tripod design also means fewer wheels to have to roll over obstacles! The bucket seat works just like the ones in high performance vehicles, it lets you use your natural body movements and trunk strength to position yourself and the stool exactly where you can do the job at hand comfortably and easily. Work without fear! The Tail Bone just rolls over obstacles that trip and tip ordinary little wheel stools. The super comfortable bucket seat is shaped and sized for real-world people, so it's not like trying to perch on a padded poke in the butt! The 100% American casters are our own design, expressly for use on creepers and carts used in auto shops, and are a combination of materials and design features not found on any other creeper wheels anywhere! The seat and the base are molded of the same tough engineering grade polymer that's used for the famously durable Bone creepers. They're smooth, impact resistant, impervious to oil, cleaners and common solvents and easy to clean. Tail Bones are 100% Made in America, designed with American ingenuity, built with quality American materials and parts brought together by American workers! We build them to do the jobs you ask of your tools,and back them with one of the strongest warranties in the business. The Tail Bone's huge 5in casters let it roll over all sorts of obstacles, from floor drains, broken floors, nuts and bolts, even air hoses! The shop version of the Tail Bone features grippy black TPE tires that allow it to grab onto and roll over obstacles. Best of all, each caster is attached to the seat with four heavy duty zinc plated 5/16in through bolts - unlike other creeper seats on the market, the wheels will never fall off! The Tail Bone ends the common frustrations found with creeper seats. Features:CastersRolls over drop light cords, cracks, grates, etc. Made in the USA 5-1/8in diameter 1in wide wheels Custom designed wheels with soft, grippy TPE tires 130 lb. rating per wheel 3/4in ground clearanceFour 5/16in bolts fasten plate – won’t breakWinged design adds style to functionBodyHigh strength polypropylene copolymer Seat is only 12in off the ground, perfect for a wide variety of jobs! 350 lb. capacity Impervious to most solvents Dirt wipes right off!SpecificationsItem Number 5031 Weight - 15.5 lbs. Dimensions 29in Long x 31.75in Wide Warranty – limited lifetime on the wheels, 1 year on the body, excludes being hit or run over. Warranties apply against manufacturer defects.  

Tail Bone Rough Rider Creeper

Tail Bone Rough Rider Creeper

Item #:

The Tail Bone Rough Rider Mechanics SeatThe Tail Bone Rough Rider is a totally new approach to creeper seats, designed from scratch to be easier to use, more comfortable, more durable and a better value than any other mechanic's stool on the market! The base is a uniquely designed tripod, so it's a naturally stable working platform even on uneven floors and surfaces. And because it turns with the user, the legs always stay out of the way and let you tuck your feet under you for comfort or convenience. The tripod design also means fewer wheels to have to roll over obstacles!The Tail Bone Rough Rider uses the casters from the Bone Rough Rider Creeper, which are 5 3/8" diameter and 1 3/8" wide, perfect for using outdoors in less than perfect circumstances. It also has an extra inch of ground clearance over the standard Tail Bone! The bucket seat works just like the ones in high performance vehicles, it lets you use your natural body movements and trunk strength to position yourself and the stool exactly where you can do the job at hand comfortably and easily. Work without fear! The Tail Bone just rolls over obstacles that trip and tip ordinary little wheel stools. The super comfortable bucket seat is shaped and sized for real-world people, so it's not like trying to perch on a padded poke in the butt! The 100% American casters are our own design, expressly for use on creepers and carts used in auto shops, and are a combination of materials and design features not found on any other creeper wheels anywhere! The seat and the base are molded of the same tough engineering grade polymer that's used for the famously durable Bone creepers. They're smooth, impact resistant, impervious to oil, cleaners and common solvents and easy to clean. Tail Bones are 100% Made in America, designed with American ingenuity, built with quality American materials and parts brought together by American workers! The Tail Bone Rough Rider's huge 5 3/8" casters let it roll over all sorts of obstacles, from floor drains, broken floors, nuts and bolts, even air hoses! Limited lifetime warranty on the wheels, limited one year warranty on the body. Features:CastersRolls over drop light cords, cracks, grates, etc. Made in the USA 5-1/4in diameter 1-3/8in. wide wheels Custom designed wheels with soft, grippy TPE tires 250 lb. rating per wheel 1-3/4in ground clearanceFour 5/16in bolts fasten plate – won’t breakWinged design adds style to functionBodyHigh strength polypropylene copolymer Seat is only 13in off the ground, perfect for a wide variety of jobs! 350 lb. capacity Impervious to most solvents Dirt wipes right off!SpecificationsItem Number 5131 Weight - 16.5 lbs. Dimensions 29in Long x 31.75in Wide Warranty – limited lifetime on the wheels, 1 year on the body, excludes being hit or run over. Warranties apply against manufacturer defects.  

Rotary Crane, 600 Lb. Capacity (Cage Code 1x747) SRC

Rotary Crane, 600 Lb. Capacity (Cage Code 1x747) SRC

Item #:

ROTARY CRANE, 600lb. capacity for FORD VanThe SRC Rotary Crane was designed to pivot in an upper and lower anchor. For use with a Service Van, the anchors are mounted to the floor and ceiling of the Van allowing the SRC Rotary Crane to pivot out of the back of the Service Van. The service technician can arc its boom over heavy loads, such as riding mowers, and easily lift either end for servicing blades, belts etc. For industrial applications the SRC can be mounted to any fixed structure for a variety of uses, such as workpiece handling in Machining Centers, Lathes and Milling Machines, putting items into dip tanks or assisting in repair or assembly. MADE IN USA  Features:Interchangeable Standard Pump Pump handle positioned to allow the operator to operate the hydraulics while guiding the load Deep reaching boom Rugged Construction... Post made with 2.375in. OD heavy wall tubing 49in. long Capacity up to 800 lbs. One Year Limited Warranty (Cage Code 1X747) Shipping Weight: 122lbs **Order the SRC for Ford Vans... and the SRC-GM for GM Vans. Dimensions & Capacity

1 2 of 2 next
SearchSpring