Ball Joint Service Tool Kit No. OTC-7249 Press Fit Ball Joint Service Tools Set The tools in this set will press in, or out, most sizes of press-fit ball joints. Plus, the C-frame press can be used alone to remove and replace universal joints.... Features: Removes and installs press-fit parts such as ball joints, universal joints, and truck brake anchor pins. Contains: 3 receiver tubes (2-3/4in I.D. x 3in O.D., 2-1/4in I.D. x 2-1/2in O.D., and 1-3/4in I.D. x 2in O.D.) Installation and removing
Heavy-Duty Universal Joint Puller No. OTC-5190 OTC Heavy-Duty Universal Joint Puller The ideal tool for disassembling drivelines... Features: May be used with up to a one-inch impact wrench. Quickly and easily removes sealed U-joint cups
Stinger Series transmission jack makes quick work of removing and installing automotive and light truck transmissions.. Features: Fully adjustable universal saddle with adjustable corner brackets and safety chain for optimum positioning of the load Flash... chromed rams that inhibit rust from entering the hydraulic system Safety overload system prevents the jack from being used beyond its rated capacity Wide leg base with 4" polyurethane swivel wheels that provide stability and easy maneuvering (Brakes
Ball Joint Service Tool with 4-wheel Drive Adapters No. APT-7865 Ball Joint Service Tool with 4-wheel Drive Adapters Ball Joint Service Tool with 4-wheel Drive Adapters Features: The heavy duty tool set is excellent for removal and installation... of press-fit parts such as ball joints, universal joint and truck brake anchor pins It will remove even rusted and corroded parts Set contains C-frame press, 3 receiver tubes sizes: 2-3/4"x3", 2-1/4"x 2-1/2" & 1- 3/4"x2", installation and removing adapters Set
is offered which makes it easier to remove the magnet from the work surface. Use to Check: Camshaft wear Valve guide wear Timing gear backlash Pinion gear backlash Driveshaft runout Disc brake runout Transmission shaft end play Specifications: Tool No.
Truck King Pin & Brake Anchor Pin Pusher With Hydraulics No. OTC-4240 Truck King Pin & Brake Anchor Pin Pusher With Hydraulics Hydraulic force and precision tooling replace torch and hammer methods to remove king pins and anchor pins... and two pins accommodate king pins of 7/8" to 2" in diameter and up to 11-1/4" long. With tooling in position, up to 30 tons of hydraulic force is applied…even the most tightly “frozen" king pin is eased out. A job that could consume the better part of a work
(Spring tension of the pull-pawl will hold the tool in place.) Then use the wrench to adjust the brake to drum clearance. Comfortable, E-Z Grip, screwdriver-style handle allows user to apply more turning power with less pressure and fatigue to the hand.... Automatic Slack Adjuster Release Tool and Wrench No. KAS-4651 Automatic Slack Adjuster Release Tool and Wrench Automatic Slack Adjuster Release Tool and Wrench These tools are used for adjusting Rockwell Automatic Slack Adjusters. The set consists
One-Man Brake Bleeder Hose No. OTC-4599 One-Man Brake Bleeder Hose Removes air from brake system–one wheel at a time– and eliminates the need for an assistant to help do the job. Features: Hose easily attaches to bleeder screw, which holds hose... in place and prevents leaking. Check-valve on end of hose prevents air from entering brake system when pumping brake pedal.
Brake Fluid Tester No. OTC-4598 Brake Fluid Tester Brake Fluid Tester Features: Tester determines quality of brake fluid. One battery included: 1.5V AAA. 1. Remove cap from brake fluid reservoir. 2. Remove probe cap from brake fluid tester. 3.... Press power button on top of tester. Green LED lights up. 4. Dip entire length of metal probes into brake fluid. 5. After one second, match color of LEDs with color chart to determine brake fluid quality. Tester automatically powers off after twelve
from OTC! It delivers up to 10 tons of hydraulic force to both remove and install truck front spring eye bushing assemblies. In many cases, the leaf spring hangers and spring assemblies can stay on the truck! Features: Works on bushings from 1-1/4"
Hub Grappler Kit No. OTC-6575 Hub Grappler Kit Hub Grappler Kit The OTC Hub Grappler Kit is the complete solution for servicing wheel hubs and bearings on the vehicle without removing the steering components or knuckle. This eliminates unnecessary... alignments or the use of a shop press, cutting service time dramatically. Features: The Hub Grappler Kit is the complete solution for servicing wheel hubs and bearings on the vehicle without removing the steering components or knuckle. This eliminates
Truck Wheel Bearing Locknut 8pt Socket 3-1/4" No. OTC-1909 Truck Wheel Bearing Locknut 8pt Socket 3-1/4" Truck Wheel Bearing Locknut 8pt Socket 3-1/4" Wheel bearing locknuts are easy to remove or install with these specially designed sockets.... They’re made of high-strength steel and resist rounding out. Note: Socket is designed for use with ¾" square drive manual tools only. Opening size (8 pt.) 3-1/4"
Lock-nut removal and installation is simple, even when wide-rim wheels are involved, since a long extension may be attached to the socket to provide the necessary clearance. Sockets are made of high-strength steel; openings resist "round-out." Display Board
Easy Lever Wheel Dolly (Large Size) No. OTC-5096A Easy Lever Wheel Dolly (Large Size) Gives technicians the leverage they need to easily remove or install truck tire-and-wheel assemblies. Features: Heavy-duty construction capable of toting 300
Truck Wheel Bearing Locknut 6pt Socket 4" No. OTC-1914 Truck Wheel Bearing Locknut 6pt Socket 4" Wheel bearing locknuts are easy to remove or install with these specially designed sockets. They’re made of high-strength steel and resist rounding out.... Note: Socket is designed for use with ¾" square drive manual tools only. Opening size (6 pt.) 4"
Brake Drum and Rotor Puller No. OTC-6980 Brake Drum and Rotor Puller Features: Handles large components such as brake drums, rotors, drive wheels, gears, flywheels, and pulleys. One person can easily set the tool in place and use for tough pulls... even where there is little access to insert the jaws. Spread to 12-3/4in. and 5in. of reach. 7-tons of force, yet weighs less than 10 pounds. Can be used with air tools to reduce time and fatigue. Patent Pending
from 11,000 to 50,000 lb. capacity. All you do is adjust and lock the jaws to the cup I.D., slip on the new cup, put it all in place, and hit the handle with a hammer. You would actually need about 30 plates to cover the range of this one tool. It does the job
Truck Wheel Bearing Locknut 8pt Socket 3-3/4" No. OTC-1925 Truck Wheel Bearing Locknut 8pt Socket 3-3/4" Wheel bearing locknuts are easy to remove or install with these specially designed sockets. They’re made of high-strength steel and resist... rounding out. Note: Socket is designed for use with ¾" square drive manual tools only. Opening size (8 pt.) 3-3/4"
Caliper Hanger Set No. OTC-7661 OTC Caliper Hanger Set Caliper Hanger Set The next time a job requires removing either front or rear disc brakes, these hangers will pay for themselves in convenience alone. Any time there's brake, wheel bearing, axle... shaft, or suspension service to do, these hangers hold the brake calipers out of the way, and at the same time, prevent damage to the brake hose.
head design quickly and easily removes the seal in one piece. This tool will last a lifetime. Built from the highest quality heat-treated steel. Removes hub seals on trailer and truck axles including truck steering axles.... Hub Oil Seal Puller No. OTC-5085 Hub Oil Seal Puller Hub Oil Seal Puller Features: Eliminates bearing and hub damage that can occur when a punch and hammer is used to remove the seal. Extra long 28in. handle provides leverage, and the unique pulling
adjusts from 37" to 55". Features: Removes, installs, and transports truck brake drums without physically having to lift them. Works on 15" and 16-1/2" drums found on most Class 7 and 8 tractor and trailer brake systems. Heavy-gauge steel construction, ten... Brake Drum Dolly OTC No.OTC-5017A Brake Drum Dolly OTC You no longer need to wrestle with truck and trailer brake drums the old way... Hard, sweaty, dirty and downright miserable. Manhandling it and hoping it doesn't fall on a foot or wreck a back
Valve Core Tool No. LIS-14100 Valve Core Tool Removes And Installs Valve Cores And Valve Core Caps. Features: The double ended core driver reverses in the tool body. The reversible driver fits both large and small valve cores. Use the reverse end... to remove and install valve core caps. The long tool handle will access inside dual wheels. The lightweight aluminum body is equipped with a pocket clip.
Truck Wheel Bearing Locknut 8pt Socket 4-3/8" No. OTC-1917 Truck Wheel Bearing Locknut 8pt Socket 4-3/8" Wheel bearing locknuts are easy to remove or install with these specially designed sockets. They’re made of high-strength steel and resist... rounding out. Note: Socket is designed for use with ¾" square drive manual tools only. Opening size (8 pt.) 4-3/8"